Community-sourced DIY repair guides for the 2011–2020 Ford F-350, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Reductant (DEF) injector urea crystallization — P208E / P218F / P20EE, the dosing test + clean-or-replace path Factory-documented(6.7L Power Stroke V8 diesel)
The reductant injector sits in the exhaust ahead of the SCR catalyst, reachable from under the truck — pulling and cleaning it is a driveway job. But the dosing measurement test (pinpoint RK7) and the SCR parameter reset need a Ford-capable scan tool; FORScan covers these trucks.
Typical difficulty: Involved — based on 72 code guides for the scr repair area (an area-level estimate, not this exact job).
Torque specs
Reductant injector mounting bolts: verify — Snug per the service manual — the injector seats in the hot exhaust; over-tightening damages the nozzle seat and gasket. Confirm torque before assembly.
Tips
This is a different campaign from the DEF tank heater note (P20BA/P20B9) — that one is the in-tank heater element. This note is the dosing injector at the exhaust: urea crystals plug its nozzle, dosing drops below spec, and the PCM sets P208E (2011-2016) or P208E/P20EE (2017-2020), sometimes with P218F, P20E8, or P204F alongside.
Ford's documented path, SSM 48539 (2017-2020): pinpoint test RK7 measures the SCR dosing output — spec is 40-50 mL. If the measurement is low, run the RK7 test two more times before condemning anything; the crystals often clear across attempts. Only if all three attempts stay below spec does the injector get replaced — and the DEF pump is explicitly NOT replaced for P208E. The 2011-2016-era SSM uses the same logic with a 45-55 mL spec and up to four additional dosing cycles.
For P20EE on 2017-2020 trucks, SSM 49202 updated the PC/ED pinpoint test RD: perform a DPF manual regeneration TWICE, then run the Specified Function SCR Parameter Reset with a Ford-capable scan tool before replacing parts. Skipping the double regen is the documented trap.
Owner tell-tales from the forums: white crystal buildup visible around the injector at the exhaust; P20E8 'reductant pressure too low' is usually the pump itself — especially on trucks built before 8/4/2011 — but one owner's truck had the pump replaced twice under warranty before the real cause (leaking injector / clogged pickup filter / unprimed pump sucking air past an O-ring) was found. Always check the build date, prime a new pump manually, and check the pickup filter in the heater/sender assembly.
Prevention is the cheap fix: hot weather evaporates DEF and leaves crystals behind, and old or contaminated DEF triggers the same codes — keep the tank capped, never drop the foil seal from a jug into the filler, and don't run the tank near-empty for weeks. Cleaning the injector nozzle with warm water (crystals dissolve in liquid DEF/water) and reinstalling with fresh seals is the owner-verified driveway fix; clear codes with FORScan and confirm the dosing measurement passes.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2011–2020 Ford F-350 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.