Community-sourced DIY repair guides for the 2011–2016 Ford F-350, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
DEF (reductant) tank heater failure — P20BA / P20B9, limp-mode countdown Owner-verified(6.7L Power Stroke V8 diesel)
The DEF tank heater assembly is under the truck at the DEF tank — a driveway job with basic hand tools, but pressure-wash the tank area first so no grit falls into the tank during the repair.
Typical difficulty: Involved — based on 72 code guides for the scr repair area (an area-level estimate, not this exact job).
Torque specs
DEF heater assembly fasteners: verify — Snug the assembly per the service manual — over-tightening cracks the plastic tank fittings; confirm torque before assembly.
Tips
The 2011-2016 F-350 6.7L DEF system has three heaters (tank, pump, pressure line); the tank heater is the common failure. P20BA is a performance code (heater drawing less current than expected) and P20B9 is the control-circuit-open code for the same heater.
Owner-measured numbers: a good heater reads roughly 1.0-2.5 ohms across the tank connector terminals; a weak one reading ~5 ohms will still melt DEF but throws P20BA. The element appears to be two parallel elements — one burns out and resistance doubles.
If the code is ignored, the truck starts a mileage countdown to limp mode (speed-limited). Replacing the heater does not always clear the countdown on its own — clear codes with a scan tool (FORScan works) and confirm the heater commands and runs.
DIY gotchas from the forums: pressure-wash the DEF tank area BEFORE opening anything (grit in the tank clogs the DEF injector or pump), drain the tank below the heater access, mark the fill/return line positions, and treat the DEF pump injector nipple as fragile — snap it and the whole pump assembly needs replacement.
Rule out the harness and the glow-plug controller before buying the heater assembly: measure heater resistance at the tank, then back-probe the circuit at the glow plug control module connector — a wiring fault is a cheaper fix than the heater.
Primary radiator plastic end-tank seam leak — the weep-to-puddle drip Owner-verified(6.7L Power Stroke V8 diesel)
Radiator R&R is a driveway job with hand tools and a helper (or a shop crane) — the radiator is tall and heavy, but nothing about the swap needs a lift. Budget a full afternoon including the refill and bleed.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Radiator mounting bolts: verify — Snug per the service manual — confirm torque before assembly; the core-support bolts are easy to over-torque with the radiator out.
Tips
The pattern: the primary radiator's plastic end tanks are crimped to the aluminum core, and the seam starts weeping — typically reported at the lower driver-side seam first. It varies from a faint antifreeze smell and a slowly dropping degas bottle to a real puddle on the concrete. Owners describe it progressing over weeks to months, not failing suddenly.
Ford's position (from the owner threads): no recall or program — customer service declined out-of-warranty coverage. But several owners got goodwill help through the FordService rep on the forums (one got Ford to cover all but $400 of the replacement out of warranty); others paid roughly $1,200 at independent shops. Worth one goodwill ask before paying out of pocket.
Replacement options owners actually used: OEM replacement (reported as reliable), or the Mishimoto all-aluminum primary (+ secondary) upgrade — but one owner reported the Mishimoto lasted less than half the miles of the original and went back to watching for drips. Mixed feedback; there is no consensus 'forever' fix, so price and warranty terms should drive the choice.
DIY pointers from owners who have done it: it's a big, tall radiator — stand on a step stool or 5-gallon bucket, tie a rope through the top eye-holes (or use a shop crane), and work the base around the fan clutch on the way out. The 6.7L has TWO radiators (primary + secondary/low-temp loop), so drain both before pulling the stack.
Refill is the fussy part: the 6.7L traps air. Either vacuum-fill, or vent via the highest hoses while filling slowly, overfill the degas bottle, then take short trips and keep re-checking the level. Pressure-test the system first to confirm the seam is actually the leak — turbo coolant feed lines and other 6.7L leak points (covered in the separate turbo-coolant-feed-line note) can put coolant in the same area.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2011–2016 Ford F-350 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.