Community-sourced DIY repair guides for the 2021–2026 Ford Bronco, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
No owner disassembly needed — the fix is a software update performed by the dealer or delivered over the air (OTA). Check Ford's recall lookup with your VIN.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
APIM software update under recall: verify — Software procedure — no torque values apply.
Tips
2021–2026 Broncos (849,310 units, plus the Edge) were recalled in March 2026 (Ford 26S09) because the infotainment Accessory Protocol Interface Module can overheat and shut down. When it does, the rearview camera image goes blank in reverse — and the entire center touchscreen goes dead for up to five minutes while the module cools.
The cause is packaging: the APIM sits too close to the HVAC ducts and the audio head unit, so under heat soak the internal temperature can reach about 105°C (221°F) and the software kills the module to protect it.
The fix is a free APIM software update, available at the dealer or as an over-the-air update on compatible vehicles. Do not pay for a new camera or touchscreen — owners on earlier camera recalls burned through camera and module replacements before the software fix was identified as the real cure.
This matters for the pre-recall repair path too: if your Bronco had a blank backup camera and the dealer replaced camera hardware, that repair may have been treating the symptom. Run the VIN and get the software update applied.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 75 complaints for the 2021–2026 Ford Bronco. 2024 was the worst year (75 complaints). Most-reported areas: unknown or other, electrical system, structure.
26V268000 (28/04/2026) — SEATS:CRITICAL FASTENERS Ford Motor Company (Ford) is recalling certain 2024-2026 Ranger and Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.
26V403000 (24/06/2026) — STRUCTURE:BODY Ford Motor Company (Ford) is recalling certain 2022-2026 Bronco vehicles. The fender flares may not be properly secured and detach from the vehicle.
24V142000 (23/02/2024) — VISIBILITY:GLASS, SIDE/REAR Ford Motor Company (Ford) is recalling certain 2023-2024 Bronco and Bronco Heritage vehicles. The rear quarter glass panels may have been improperly installed to the vehicle hard top, which can allow them to detach.
26V468000 (20/07/2026) — ENGINE Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
25V025000 (17/01/2025) — SUSPENSION:REAR:SHOCK ABSORBER Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco vehicles. The rear shock absorbers may corrode and fail, resulting in detachment of the external reservoir.
24V770000 (16/10/2024) — SUSPENSION:FRONT:CONTROL ARM:UPPER BALL JOINT Ford Motor Company (Ford) is recalling certain 2024 Ranger, and 2024-2025 Bronco vehicles. The front upper control arm ball joint nut may not have been installed or tightened properly, allowing the front upper control arm to detach from the knuckle…
16 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2021–2026 Ford Bronco yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.