Community-sourced DIY repair guides for the 2007–2007 Dodge Nitro, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Dealer service — no owner teardown needed. The fix is external relays plus a TIPM software update.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Typical time: “Chrysler's own owner letter puts the relay portion at about an hour.” — as written in the note. First-timers often take twice this.
Torque specs
Wiper relay / TIPM service hardware: verify — Dealer-performed recall work — no owner torque specs involved.
Tips
NHTSA campaign 09V438000 / Chrysler J28 covers certain 2007 Nitros (~84,680 units): heavy use of the delay/intermittent wiper setting can destroy the wiper relay inside the TIPM and eventually kill the wipers entirely.
The dealer remedy is free: inspect the TIPM, add external wiper relays, and update the TIPM software. Chrysler's own owner letter puts the relay portion at about an hour.
Symptom pattern: wipers work on some speeds but die on delay, or quit altogether after a period of heavy intermittent use — that points at this recall, not the wiper motor.
This is the same TIPM family behind the Nitro's broader 'possessed' electrical behavior (wipers, horn, headlights acting on their own); if the recall work is done and gremlins persist, a rebuilt or replacement TIPM is the documented next step per a Nitro owner walkthrough.
Check any 2007 Nitro by VIN for open J28 before spending money on a wiper motor or switch.
Dealer service — the fix is a TIPM software reflash. No parts are replaced.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
TIPM software reflash: verify — Dealer-performed recall work — no owner torque specs involved.
Tips
NHTSA campaign 07V-291 / Chrysler G25 covers ~80,894 model-year 2007 Wranglers and Nitros built January 30, 2006 through January 22, 2007: TIPM software could trigger an internal 75 ms reset cycle in response to bus errors.
During the reset the TIPM's 'key on' signal to the PCM drops out; the PCM reads it as the ignition being switched off and begins a power-down — the engine stalls, sometimes restarting on its own from rotating inertia, sometimes needing a key restart.
The telltale signature owners described: a momentary loss of electrical power with the instrument-cluster warning lamps flashing during the event.
The revised software (in production from January 22, 2007) shortens the TIPM reset to 17 ms, which removes the PCM power-down window — the dealer reflash applies the same fix.
If a 2007 Nitro stalls with flashing cluster lamps and no codes, check for open G25 before replacing sensors or the PCM.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2007–2007 Dodge Nitro yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.