Community-sourced DIY repair guides for the 2015–2015 Chrysler 200, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Dealer recall — the Power Distribution Center is under the hood. There is no driveway equivalent to this fix; the recall work itself is the fix, free of charge.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Recall repair: verify — No torque-critical fasteners in this dealer repair for the owner — the connector/harness replacement is covered by the recall.
Tips
The signature failure is a sudden stall without warning while driving, sometimes with the electrical system cutting out first — the C4 connector in the Power Distribution Center loses contact intermittently. Do not start by buying sensors; check whether recall R24 is open on your VIN first.
The fix is a free dealer repair under FCA campaign R24 (NHTSA 15V-470), covering about 77,834 early-build 2015 200s (January 7 to September 23, 2014). On 3.6L cars the dealer replaces the C4 connector with a 12-wire split kit; on 2.4L cars it replaces the transmission wiring harness.
Some owners report the stall returning after the R24 repair was done — if yours keeps dying after the recall visit, have the dealer re-inspect the connector work before paying for unrelated parts like coils or a throttle body.
If you experience a no-warning stall in traffic, treat it like any sudden power loss: coast to the shoulder, hazards on, and get the car to a dealer for the free inspection rather than driving on with an intermittent connector.
Park rod / park lock recall (R08) Factory-documented(3.6L Pentastar V6)
Dealer recall work — the dealer inspects the transaxle's internal park rod and tests the park pawl; a transaxle with a damaged rod or binding pawl is replaced outright, free of charge.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Recall repair: verify — No torque-critical fasteners for the owner — the inspection and any transaxle replacement are covered by the recall.
Tips
The defect: on affected 2015 200s with the 3.6L V6 and 9-speed transaxle, the internal park rod may have been damaged during manufacturing, or assembly debris can bind the parking pawl — so the shifter can show Park while the transaxle never actually locks, letting the car roll away.
This one is 200-specific to early-build cars: FCA campaign R08 (NHTSA 15V-090) covers 2015 200s built March 9 through December 15, 2014 with the 3.6L/9-speed combination — about 21,466 cars. If your car is in the window, get the free inspection even if it has never rolled.
The dealer remedy is inspect-and-test, then replace the whole transaxle if the rod is damaged or the pawl binds — free, and the owner letter warns the work can take up to eight hours, so schedule accordingly.
Owner habit that costs nothing: always set the parking brake, especially on any slope, until you know this recall is closed on your car. A car that 'feels' like it is in Park but is not is exactly the failure mode here.
Dealer recall — the dealer inspects the rear shock absorber build date codes and replaces any shock in the suspect range, free of charge.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Typical time: “The free dealer check under FCA campaign P37 (NHTSA 14V-392) is quick: about half an hour to read the shock date codes, and if yours fall in the suspect range the shocks are replaced — roughly 1.5 more hours, parts and…” — as written in the note. First-timers often take twice this.
Torque specs
Recall repair: verify — No torque-critical fasteners for the owner — shock inspection and replacement are covered by the recall.
Tips
On a narrow build window of 2015 200s (those fitted with Hitachi rear shocks from May 21 through June 5, 2014), a supplier inspection miss means the weld on the shock's attachment ring can be too weak for the vehicle's load — a partially detached rear shock can then damage chassis parts, the rear brake tube, or the tire.
The free dealer check under FCA campaign P37 (NHTSA 14V-392) is quick: about half an hour to read the shock date codes, and if yours fall in the suspect range the shocks are replaced — roughly 1.5 more hours, parts and labor free.
Warning signs worth a look even before the recall visit: new clunking from the rear over bumps, or visible shock damage/leakage on a 2015 in this build window. A failed shock that lets go at speed can take the brake tube with it, so do not keep driving on it.
About 20,300 vehicles across the 2015 200, 2014 Cherokee, and 2014 Ram 1500 share this campaign; check your VIN to see whether your 200 is in the affected slice.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2015–2015 Chrysler 200 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.