Community-sourced DIY repair guides for the 2009–2017 Chevrolet Traverse, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Blend door actuator clicking / temp control loss Owner-verified(3.6L LY7/LLT/LGX V6)
Behind the glove box and driver-side dash. Drop the glove box fully open by pressing in the side tabs; the actuator is held by small bolts — the rear bolt is the fight, and owners grind down a 1/4-inch 8mm socket to reach it.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Actuator mounting bolts: verify — Small mounting bolts; torque not confirmed from a forum source — snug against factory service info, these strip easily in the plastic housing.
Tips
Diagnose by sound: a rapid clicking from behind the glove box or dash right after startup or when changing temperature/mode settings is the actuator's internal plastic gear stripped of teeth — the motor keeps spinning against the broken gear.
Symptoms beyond the noise: temperature stuck on full hot or full cold, driver-side and passenger-side disagreeing, or the mode selector refusing to switch between vent, floor, and defrost.
The fix is a replacement actuator — an inexpensive part and a driveway job on these cars. Swap it, then recalibrate: pull the HVAC/ECAS fuse for at least 10 seconds, reinstall it, start the vehicle, and give the HVAC control module 40 seconds to self-calibrate with no scan tool needed.
If a new actuator still doesn't fix it, the blend door itself may be broken or jammed inside the HVAC housing — check for a binding door before buying a second actuator.
OEM part number seen on 2011 models is 15920864; confirm the year-matched part for 2013+ cars, since the actuator design changed.
Straightforward bolt-on job — caliper off, rotor off, hub bolts out, hub off. No press needed; the unitized hub bolts to the knuckle. Watch the ABS sensor harness routing on reassembly.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Torque specs
Axle nut: verify — Axle-nut spec not confirmed from an owner source — confirm against factory service info before torquing.
Tips
The classic failure is a humming/growling that changes with road speed and gets louder or quieter when you drift left vs. right — one owner's confirmed fix was the left front hub, and the ride got noticeably quieter.
The hub's ABS sensor and tone ring are integrated, so a failing hub can also set C0035/C0040 (front wheel speed sensor codes). Diagnose before replacing — a dirty reflector ring on the back of the hub fooled at least one owner into chasing a sensor instead.
Moog 513277 is the listed front hub fitment for 2009-2017 Traverse (verify by drivetrain — FWD vs AWD axle spline differs).
Tighten the axle nut with the vehicle's weight on the ground and spin the wheel while tightening — the generic procedure; confirm the actual spec against factory service info.
Don't confuse bearing hum with CV joint noise: CV problems click or pop on turns, bearings drone on straights and change tone with steering load.
Spark plugs and coils — 100k service / misfires Owner-verified(3.6L V6)
Front-bank plugs are easy; the rear bank requires removing the upper intake manifold. Labor guides book 2.4 hours for all six — plan a half day if the intake is your first.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Typical time: “Labor guides book 2.4 hours for all six — plan a half day if the intake is your first.” — as written in the note. First-timers often take twice this.
Torque specs
Spark plugs: 13 ft-lb — 13 ft-lb per a GM tech Q&A answer — confirm against factory service info.
Intake manifold: verify — Upper-intake torque sequence and spec not confirmed from an owner source — confirm against factory service info.
Tips
To reach the rear-bank plugs you must remove the upper intake manifold — a new intake gasket is required on reassembly, torqued to spec, or you'll introduce an air leak.
Use AC Delco/OEM plugs (GM 19300872) and coils (GM 19418102) per a GM tech Q&A answer; gap to 0.043 in. and torque plugs to 13 ft-lb (confirm against factory spec).
Misfires on these engines also disable traction control — that's normal behavior, not a second failure.
Chase a stubborn single-cylinder misfire by swapping the coil to another cylinder and watching the code follow it before buying parts. Check coil connectors are fully locked — broken connector locks cause intermittent misfires.
If the misfire comes with cam/crank sensor codes, suspect timing-chain issues (see the timing-chain note) rather than ignition.
Rear AC line corrosion / leak (aux A/C goes warm) Owner-verified(3.6L V6)
Underbody work — the aluminum lines run along the frame rail to the rear evaporator. GM's official fix replaces the bad section with a splice; owners often route a rubber hose assembly alongside instead.
Typical difficulty: Easy — based on 16 code guides for the ac repair area (an area-level estimate, not this exact job).
Torque specs
A/C fittings: verify — Fitting torque not confirmed from an owner source — confirm against factory service info before torquing.
Tips
The signature: front A/C blows cold, rear blows warm (or the system loses charge over weeks). On the Traverse the vapor line feeding the rear AUX unit develops pinholes, often where brackets hold the line to the frame.
Diagnose with UV dye in the system — the leak location is usually visible once you look along the rail. A documented owner case on the related GM platform had the line corrode exactly at the frame bracket.
GM part 23199274 (tube aux A/C evaporator) was the identified replacement for one 2012 Traverse case — verify fitment by VIN; the pipe assembly is a sub-$100 part, but routing is the labor.
The official GM repair is a splice of the failed section; a cheaper owner route is having an A/C shop build rubber hose lines reusing the original end fittings. Either way the system must be evacuated, O-rings replaced (lubed with compressor oil), vacuumed, and recharged to the underhood label weight.
While it's open, the orifice tube (in the line between the schrader valves) is cheap to replace and collects compressor debris — owners recommend doing it.
Front struts and strut mounts — clunking, float, tire wear Owner-verified(3.6L V6)
Straightforward strut work — loaded/quick-strut assemblies (strut + spring + mount preassembled) eliminate the spring compressor entirely. An alignment is required afterward.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Torque specs
Strut fasteners: verify — Fastener torque not confirmed from an owner source — confirm against factory service info before torquing.
Tips
Worn struts on these show as front-end clunking over bumps, a floaty ride, and cupped tire wear — one owner's 2010 was fully solved with a KYB Strut-Plus set.
Always replace the top strut mounts with the struts. A documented case: a Traverse clanged after a strut-only replacement because the old mounts were reused — mounts are the usual clunk source, not the strut itself.
Loaded assemblies (Monroe 172518 for 2009-2012, 172949 for 2013-2017, per Monroe's fitment bulletin — confirm by year) are the DIY-friendly choice: no spring compressor, no fighting a rusted mount.
You will need a wheel alignment after front struts — the struts set ride height. Rear shocks don't affect alignment, so those can be done separately.
Low-speed parking-lot clunk that survives new struts and mounts may be sway-bar links or control-arm bushings — diagnose before throwing more parts.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 646 complaints for the 2009–2017 Chevrolet Traverse. 2012 was the worst year (354 complaints). Most-reported areas: air bags, engine, electronic stability control (esc).
15V415000 (30/06/2015) — STRUCTURE:BODY:HATCHBACK/LIFTGATE General Motors LLC (GM) is recalling certain model year 2008-2012 Buick Enclave vehicles manufactured January 3, 2007, to February 29, 2012, 2009-2012 Chevrolet Traverse vehicles manufactured July 6, 2008, to March 9, 2012, 2007-2012 GMC Acadia vehicles manufactured September 15…
15V609000 (29/09/2015) — VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR General Motors LLC (GM) is recalling certain model year 2016 Chevrolet Traverse, GMC Acadia, and Buick Enclave vehicles manufactured August 18, 2015 to September 24, 2015. Due to a manufacturing defect, the windshield wiper motor may overheat when used.
14V266000 (20/05/2014) — SEAT BELTS General Motors is recalling certain model year 2009-2014 Buick Enclave vehicles manufactured April 14, 2008, through May 14, 2014, Chevrolet Traverse vehicles manufactured June 6, 2008, through May 14, 2014, and GMC Acadia vehicles manufactured April 9, 2008, through May…
14V118000 (17/03/2014) — AIR BAGS:SIDE/WINDOW General Motors LLC (GM) is recalling certain model year 2008-2013 Buick Enclave and GMC Acadia and 2009-2013 Chevrolet Traverse and 2008-2010 Saturn Outlook vehicles. In the affected vehicles, increased resistance in the driver and passenger seat mounted side impact air…
15V833000 (11/12/2015) — SEATS General Motors LLC (GM) is recalling certain model year 2016 Chevrolet Traverse, GMC Acadia, and Buick Enclave vehicles manufactured November 6, 2015, to November 12, 2015. The affected vehicles have a the third row left lower seat frame that may…
23V334000 (10/05/2023) — AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE General Motors, LLC (GM) is recalling certain 2014-2017 Buick Enclave, Chevrolet Traverse, and GMC Acadia vehicles. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
9 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2009–2017 Chevrolet Traverse yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.