Community-sourced DIY repair guides for the 2021–2022 Buick Envision, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Fuel pump control module failure Factory-documented(2.0L LSY Turbo I4)
The fuel pump power control module lives in the rear of the vehicle near the fuel tank. On recalled vehicles the dealer replaces it free under the emissions recall — do not pay for this part yourself before checking your VIN against the campaign.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
Fuel pump power control module: verify — Dealer-replaced under the recall; no owner torque spec found — verify against service info if doing this outside the campaign.
Tips
If a 2021–2022 Envision stalls, loses power, or struggles on hot restarts, check the VIN against GM emissions recall N252516900 before buying any fuel-system parts — the fuel pump power control module is prone to failure and interrupts fuel flow to the engine.
This is an emissions recall, not a safety recall: GM's own dealer bulletins (updated as recently as January 2026) kept moving additional VINs to open status, so a VIN that showed clear last year may be covered now. Verify in GM's IVH before paying for anything.
The dealer remedy is a free module replacement pending inspection. Related: the earlier store note on 2007–2014 full-size trucks covers a different FPCM problem (water intrusion at the connector), not this campaign.
If you get a no-start with fuel pressure present at the rail, the module is the prime suspect; if pressure is absent, the pump itself is back on the table. The recall applies only to the module.
The fix is a BCM reprogramming done through GM's Service Programming System — dealer-only, but it is the documented correction, not a parts replacement.
Torque specs
Liftgate hardware: verify — No hardware replacement per the bulletin — verify against service info if replacing any liftgate component.
Tips
On 2021–2022 Envisions the kick-to-open liftgate works intermittently or barely responds. Rule out technique first: kick straight under the driver's side of the rear bumper, left of center, with the key fob within 3 feet — the Buick logo projected on the ground marks the spot.
If technique is right and the kick feature still misses, GM technical bulletin 21-NA-286 names the cause: the hands-free liftgate software doesn't recognize certain kick motions. The correction is reprogramming the BCM with the latest software — do not replace the liftgate sensor or actuator.
After inspection and diagnosis that finds no hardware fault, the dealer follows the bulletin procedure via SPS2. Honest caveat: this is bulletin-anchored with GM's own procedure text rather than a long owner fix-confirmation thread, but the documented path is software, not parts.
Also check Settings > Vehicle > Comfort and Convenience > Hands-free Liftgate Control — the kick function can be set to off, open-only, or open-and-close, and a turned-off setting mimics a dead sensor.
Diagnosis per GM service information: compare ECT sensor readings against each other with a scan tool. The fix is sensor replacement once the faulty reading is isolated — dealer-level diagnosis, cheap part.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
ECT sensor: verify — No owner torque spec found — verify against factory service info before installing.
Tips
If a 2021–2022 Envision's 2.0L LSY runs hot or throws an over-temperature warning without an obvious coolant loss, check the engine coolant temperature sensor before the thermostat, water pump, or radiator: GM documents a faulty ECT sensor that reads noticeably cooler than the other ECT readings.
The bad reading mispositions the engine coolant control valve, starving the radiator of flow — so the engine overheats while the sensor insists everything is fine. That's why the temperature gauge can look normal while the dash screams over-temp.
The documented path: run GM's engine-overheating diagnostics per service information first; if that doesn't isolate a cause, the ECT sensor is the prime suspect. Replace the sensor, not the cooling system around it.
Honest caveat: this leans on GM's own diagnostic guidance plus press coverage rather than a big owner thread, and real overheating still needs the basics checked first (coolant level, leaks, fan operation). But it saves a thermostat-and-pump replacement that fixes nothing.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2021–2022 Buick Envision yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.