2009–2014 Audi Q5

Community-sourced DIY repair guides for the 2009–2014 Audi Q5, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.

Owner-verified repair guides

2.0T EA888 oil consumption Owner-verified (2.0T)

Check the PCV unit first: with the engine idling, pull the oil filler cap. If the cap is glued down by extreme crankcase vacuum, or if you hear a whistling/squealing from the cam cover area, the PCV diaphragm has failed and is drawing oil into the intake. The PCV on the Gen-2 EA888 2.0T sits on top of the camshaft cover, held by a handful of Torx screws — about a 20-minute swap. Buy the latest revision of the genuine VW/Audi part; owners warn the cheap aftermarket clones fail again. If the PCV is healthy and the car still burns oil, you are dealing with the piston rings: an extended upper-cylinder soak (owners use Berryman B-12 in the plug wells, several hours to overnight, then fresh oil) can free lightly carbon-clogged oil control rings, but severely clogged or low-tension rings need the pistons and rings replaced.

Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).

Tips

Sources: AudiWorld: 2015 Q5 2.0T oil consumption (ring design explanation) · AudiWorld: 2014 Q5 extreme oil consumption (clogged ring passages) · AudiWorld: Yet another 2.0T oil consumption issue (PCV first, soak option) · AudiWorld: A4 B8 oil consumption info (CAEB incl. Q5; 1 qt/1,200 mi spec) · Audi AWA-15-04: oil consumption warranty extension 2009-2011 (8yr/80k) · TopClassActions: 2012-2014 Audi piston settlement (9yr/90k, 75% repair)

No owner reports yet — fixed this yourself? tell us how

Timing chain tensioner Owner-verified (2.0T)

VCDS gives you the early look the dashboard never will: go to Engine, Advanced Measuring Values, and add 'camshaft adaptation intake bank 1 phase position' — the measured deviation of the intake cam phaser from target. Check it at full operating temperature (values worsen under load and heat); a stretched chain shows as rising deviation. There is no reliable early warning from driveability — when the chain or tensioner lets go it skips teeth with little notice, the pistons hit the valves, and you are looking at head work at best or a replacement engine. If the deviation is high, or the old tensioner revision is still fitted on a 2009-2012 car, replace the tensioner, chain, guides, and related bolts as preventive maintenance; owners do the water pump at the same time since it is right there.

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: AudiWorld: Q5 timing chain failed at 70k (VCDS phase-position check) · AudiWorld: 2.0T timing chain tensioner (no warning, preventive replacement) · AudiWorld: 2015 Q5 timing chain fail (open case with Audi, use indy shop) · AudiWorld: 2013 Q5 2.0 timing chain issues (dealer report, tension notches)

No owner reports yet — fixed this yourself? tell us how

Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

What owners report

NHTSA recorded 4 complaints for the 2009–2014 Audi Q5. 2012 was the worst year (4 complaints). Most-reported areas: structure, suspension, air bags.

Counts are NHTSA complaints filed for these model years, via the NHTSA API. See data for all Q5 years →

Recalls

6 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.

Factory service bulletins

We don't have factory bulletin data for the 2009–2014 Audi Q5 yet.

Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.

Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.