Community-sourced DIY repair guides for the 2012–2018 Audi A6, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Passenger side: loosen the clamps on the air intake tube, detach the filter-box end and move it aside for clearance. Remove the 2 torx screws holding the coil-pack harness down, unhook each connector, and slide the harness off the coil packs; pull coils straight out. Driver side: the coolant expansion reservoir blocks access — unscrew it from its bracket and disconnect the coolant-level sensor on the bottom, then shift it forward and to the side WITHOUT disconnecting the main lower hose (which has little slack) to reach the coils.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plugs: 30 Nm — From Audi repair manual (erwin) per forum DIY author.
Coil-pack harness torx screws: verify — Confirm against factory service info before torquing.
Tips
Coil packs may be seized in the wells — a coil puller beats channel-lock pliers on the connector casing, which can crack the plastic.
Unhook the clip that holds part of the coil-pack harness to the cylinder head for extra harness slack on the driver's side.
Replace one plug at a time to track per-cylinder plug condition.
Anti-seize on plug threads and dielectric grease inside the coil boot are called out in the Audi repair manual.
Front pads only need the caliper removed: take off the T45 torx screw on the caliper anti-rattle spring, pop the two plastic caps off the back of the caliper, and remove the two guide pins with a LONG 9mm hex bit (standard length won't reach). For rotors, also remove the two 22mm carrier bolts first — make sure you can crack these loose before starting, as they are extremely tight and room in the wheel well is limited. The rotor is held by a T30 torx screw and is typically rust-frozen to the hub, needing PB Blaster and hammer work.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Caliper guide/slide bolts: 35 Nm — Replace the bolts each time they are removed (per video walkthrough).
Caliper carrier bolts: 196 Nm — Replace the bolts each time; breaker bar needed to loosen.
Wheel bolts: 120 Nm — ASE tech answer for 2018 A6.
Tips
Loosen lug bolts while the car is on the ground; jack as high as possible for carrier-bolt room and set a stand before removing the wheel.
Never let the caliper hang from the brake hose — rest it on a bucket or similar.
Pad wear sensor is on the driver's (left) side: twist it 90° to release it from the bracket.
Front calipers push straight back (no EPB on the fronts); siphon some fluid from the reservoir first or it may overflow when pistons are compressed.
The 12V battery is trunk-mounted under the spare tire — remove the cargo floor, spare tire, and tool kit to reach it. Remove the hold-down clamp, disconnect negative first, then positive; note the vent breather tube plugged into the side of the battery — it vents gases outside the car and is easy to miss on reinstallation. Registration/adaptation IS required: recode the BEM info (capacity in Ah, manufacturer, serial number) via VCDS or OBDeleven in the battery regulation control unit so the charging system treats it as a new battery.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Torque specs
Battery hold-down clamp: verify — Confirm against factory service info before torquing.
Battery terminal clamps: verify — Confirm against factory service info before torquing.
Tips
Hook the under-hood jump terminals to a charger/memory saver during the swap to avoid stray reprogramming needs.
Put plastic or cardboard in the battery well near the positive post so it can't short against the compartment walls.
If the replacement battery has no BEM code sticker, change the last digit of the currently stored serial number and update the Ah value to the new battery's rating.
Skipping registration shortens the new battery's life: the smart charging system keeps charging it as if it were the old worn battery.
Keep a booster on the hood terminals if the trunk won't open with a dead battery — then the trunk release works.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 110 complaints for the 2012–2018 Audi A6. 2012 was the worst year (59 complaints). Most-reported areas: engine, air bags, electrical system.
15V019000 (20/01/2015) — FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2011-2012 Audi S4, S5, Q7, 2012 Audi A6, Volkswagen Touareg Hybrid, and 2012-2013 Audi A7 vehicles. In the affected vehicles the fuel injection system may experience a fuel leak.
19V035000 (16/01/2019) — FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL Volkswagen Group of America, Inc. (Audi) is recalling certain 2016-2018 Q7, A6 and A7 vehicles, and 2015-2018 Audi A8 vehicles. The left and right fuel rails may leak fuel.
18V229000 (11/04/2018) — ENGINE AND ENGINE COOLING:COOLING SYSTEM Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2013-2017 Audi A5 Cabriolet, A5 Sedan and Audi Q5 vehicles, 2012-2015 Audi A6 vehicles and 2013-2016 Audi A4 Sedan and A4 allroad vehicles. These vehicles, equipped with 2.0l Turbo FSI engines…
15V823000 (08/12/2015) — AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2012-2013 Audi A6 vehicles manufactured March 28, 2011, to March 25, 2013, and 2012-2013 Audi A7 vehicles manufactured January 25, 2011, to March 19, 2013. In vehicles with heated…
16V646000 (07/09/2016) — FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2012-2013 Audi A6 and Audi A7 vehicles. The affected vehicles have a fuel hose in the engine compartment that may degrade and leak fuel.
17V781000 (06/12/2017) — FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2012-2014 Audi A6 and A7 vehicles. The fuel line has a compression point that can weaken, potentially resulting in a fuel leak.
10 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 2,787 manufacturer communications (service bulletins, dealer notices) covering the 2012–2018 Audi A6.
Most cited systems: Equipment (835), Electrical System (721), Engine And Engine Cooling (384), Engine (208), Power Train (176).
Latest bulletins:
TSB_2074436_3 (Aug 2026) — Unknown Or Other
TSB_2069078_4 (Aug 2026) — Service Brakes
TSB_2069904_3 (Aug 2026) — Service Brakes
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.